When it comes to fine mechanical drives and assemblies ...




We support: As a consultant and / or producer



With our experience, we manufacture, as a prototype and in series, for the gas industry, photo-optical industry, textile machinery, printing machinery, gear manufacturers and medical technology.



Our manufacturing width



Precision actuators and assemblies
* Industry-specific drives

* Helical gear

Verzahnugsbaugruppen
Precision Turned Parts
Turntables


With consistency to success



Your imagination and ideas
joint analysis
Development and prototype
Use our know-how
Single or series production
trained and motivated employees on modern machines
Custom Integration
cross-industry experience coupled with technical engineering potential

The company August Feldmann, was founded in 1937 as Lohndreherei for castings in Velbert, then the center of the German foundry industry. In the economic boom years of the establishment of a comprehensive standard parts program for the commercial vehicle, agricultural machinery and automotive industry began.



The high manufacturing quality and in particular the ability to create short-term solutions for individual requirements by technical advancements have led to close ties with customers - outside of Germany. So, for example, twisted clevises developed as a replacement for the much more expensive forged copies of the late 50s into an export success.



1972 & Co. KG was the transformation take place in a limited company. Partner is the August Feldmann GmbH. The limited partnership is 100 percent family owned. The management is responsible since 1995 Dipl.-Ing. Christian Feldmann.

Portrait of the company Felker Drehtechnik

The company Felker rotation technique was founded by Mr. Gerhard Felker and his wife Verica Felker as a pure contract manufacturing companies in D-89610 Oberdischingen in December 2004.

The range consists mainly in the manufacture of automatic lathe parts (valve seats, valve pistons, valves, anchors, piston, pin, spring plate, lathe parts, micro turned parts, micro-turning), made of steel such as 9S Mn Pb 28K, 16 Mn Cr5 C 45, 42 Cr Mo4 Stainless steel to 1.4301, 1.4305, 1.4105 (X6Cr Mo S17), cast iron, aluminum (Al Mg Si) and brass (to Zn 39 Pb) on 9 Tornos AS 14 six-spindle automatic lathes up to Ø 14 and an additional plastic on a Star lathes up to Ø 16 in Central series and large series from a lot size of 20,000 or 5,000 units at long lathe.

Besides this installation work, Nachdreharbeiten and Deburring and Aussuch or testing work of rotary parts of all kinds are carried out.

Our strength lies in the flexibility of the company.An absolutely smooth cooperation among the employees as well as with senior management and the customer ensures virtually zero defect deliveries.

We endeavor to expand and consolidate its above-average quality, our previous successful and trusting relationship with our customers.

Our goal is to provide systematic improvement in quality and on time delivery to satisfy the customer and implement its requirements given us 100% error-free and at a reasonable cost. We are certified according to DIN EN ISO 9001:2000 and reject ourselves to the standard DIN ISO TS 16949.

Be able to work more efficiently in addition to three of these aircraft were purchased, which have been found in our new premises good place.

The new building has a production area with warehouse and office of approximately 1000 m², as well as buildings for more than one employee / inside of about 170 m².

Our production capabilities:
- CNC turning and milling center for complex machining
Thread rolls / rooms / sandblasting
- Grinding (centerless, cylindrical and surface grinding)
- Deep-hole drilling

Our strengths:
- Quality
- Advice and support of our customers
- Solution orientation
- Extensive experience - broad know-how
- Fast project implementation thanks flexiebler applications
- Manufacture of complex parts
- Modern machinery
- Environmentally sound management of all processes

Textile logistic and solutions.
Trucks to load/unload warp beams and fabric rolls on looms.
Winders and rolling machines

We are the leading manufacturer of manual and fully automatic operating

Multispindle Drilling and Grinding Machines for Brake linings and Clutch facings

For more than 50 years our products have been valued by the major friction material producers world-wide.

The company has been founded in 1955 by the Engineer Ferdinand Erlmann. Due to his former activities he had best contacts to the Brake Lining and Clutch Facing Industry in Germany so that he could get a good overlook of their requirements.

He developed efficient production technology for drilling of brake linings and clutch facings. To fulfil the demand of our customers he designed as well Hand Drilling Jigs for a low production rate as automatically working machines for economic drilling of big runs.

In 1972 Ferdinand Erlmann incorporated a partnership with Rolf Stratmann and in 1987 he retired. Rolf Stratmann assumes the complete participations. 2007, 65 years old, he assigned the company to
Dipl. Ing. Gerd Schorn and he continue the business.

Beside of our standard machinery program several special purpose machines have been built according to the requirements of our clients. Our Engineering department persistently develops the machines with high-precision components according to the newest technology. The requested quality regulations for the original equipment of the most important motorcar and axle producers as DAIMLER CHRYSLER, VW, GENERAL MOTORS, DAF, DANA, BERGISCHE ACHSEN, MAN, MERITOR, ROCKWELL, SCANIA, FRUEHAUF, LEYLAND, VOLVO, PEGASO, KAESSBOHRER, IVECO a. s. o. will be completely fulfilled.

As producer of high quality machinery on a small and specialised market a personalised service to our customers is the first priority for us.

Ferhat Karahatil Maschinenbau manufactures machine parts and components in various materials.
Our core business is prototypes, individual and series parts with a diameter of 1 mm to 100 mm and a maximum length of 300 mm.
Other processes and sizes can be implemented with partner companies.

Our company has specialized in the processing of simple to complex parts.
You can expect products with high precision. Your demands determine the quality of our work.

We would be happy to advise you in a non-binding discussion. We are at your side from the planning to the construction phase.

imprint
According to § 5 TMG
Ferhat Karahatil
Ferhat Karahatil mechanical engineering
At the craft center 1
A3
52156 Monschau-Imgenbroich

Details of the liability insurer:
Allianz Insurance AG
No .: AS-9235662119

Contact:
Phone: 015228401131
Email: f.karahatil@gmx.de
Sales tax ID Sales tax identification number in accordance with Section 27 a of the Sales Tax Act: DE 335264528

The company Fermes deals with service processing of brass, aluminum and steel on CNC lathes and milling machines. In its machine park, it has 4 CNC lathes brand and model HAAS ST-10, 4 automatic CNC lathes with bar feeder brand and model HAAS CL-1, as well as 1 CNC milling machine brand and model HAAS VF-1. In addition to CNC equipment, Fermes also owns two channel two-chamber induction (casting) furnaces, deals with casting brass in molds, and also has a hot pressing (forging) machine.

We manufacture prototypes and series of precision mechanical parts in aluminum alloys, steel, stainless steel, plastic, Teflon and titanium, for an exclusive clientele in the automotive and motorcycle racing sectors, aeronautical and aerospace vehicles, automatic machines for industry and packaging and dental implantology. We create the finished part starting from the customer's drawing or 3D model, with control and validation of the production process and product traceability:
- design with Cad / Cam software, Virtual Machining and control plans with Solid Inspection - import from any standard CAD format
- manufacturing of parts from solid with continuous milling on 3-4-5 axis machining centers on palletized machines, turning, EDM, drilling, lapping and finishing
- special processes (heat and surface treatments) carried out in collaboration with the best partners on the market
- tests in the metrology room at controlled temperature and humidity set up with 3D measuring machines, control certificate with penetrating liquids performed by qualified 2nd level personnel
- industrialization processes validated with FAI and configuration management
- product traceability guaranteed with test reports and issue of the certificate of conformity
- quality management system certified according to the aeronautical standard UNI EN 9100 and according to UNI EN ISO 9001

For over 40 years we have been at the forefront of technology to offer the customer the highest quality available on the market for complete, customized solutions, guaranteed in quality, delivery times and after-sales assistance.